Troubleshooting Video
Water loss in a pond, stream, or waterfall may be caused by evaporation, splashing, low liner edges, plumbing leaks, or damaged pond liner. Before making repairs, determine whether the water loss is normal or caused by a leak.
Step 1: Check for common causes of water loss
Inspect the pond, stream, and waterfall for these common problems:
- Evaporation: Hot weather, wind, low humidity, and moving water can increase evaporation.
- Low liner edges: Settling soil can lower the liner edge, allowing water to escape.
- Waterfall splashing: Water may splash outside the lined area.
- Debris buildup: Leaves, rocks, or other obstructions can redirect water over the stream or waterfall edges.
- Plumbing leaks: Cracked pipes, loose fittings, or damaged connections can cause water loss.
- Liner damage: Punctures, tears, or improperly installed liner can allow water to escape.
- Skimmer or filter leaks: Damaged seals or connections around the skimmer or BioFalls filter can allow water to escape.
Look for unusually wet soil, exposed liner, or water flowing outside the intended area.
Step 2: Perform a pump-off water-level test
A pump-off test helps determine whether the leak is in the pond or in the stream, waterfall, or associated plumbing.
- Fill the pond to its normal operating water level.
- Mark the water level for reference.
- Turn off and unplug the waterfall pump.
- Monitor the pond water level for up to 24 hours.
- Check whether the water level continues to drop.
Important: If fish are present, maintain adequate aeration and oxygen levels while the waterfall pump is off. Do not leave fish without sufficient oxygen or necessary filtration.
If the water level continues dropping
The leak is likely in the pond itself or an area connected to the pond, such as the liner or skimmer.
- Allow the water level to continue dropping while maintaining safe conditions for fish.
- Observe where the water level stabilizes.
- Inspect the liner, skimmer, and surrounding areas near that elevation for damage or leaks.
If the water level remains stable
The leak is more likely associated with the stream, waterfall, plumbing, or filtration components used when the pump is running.
Proceed to Step 3.
Step 3: Inspect the stream and waterfall
If water loss occurs primarily when the pump is running, inspect the stream and waterfall for escaping water.
- Check for low liner edges caused by settling soil.
- Inspect rocks that may redirect water outside the lined area.
- Remove leaves, gravel, or debris obstructing water flow.
- Look for excessive splashing along the waterfall.
- Check the stream and waterfall edges for wet soil.
To correct a low liner edge:
- Carefully lift the surrounding liner edge.
- Add compacted soil underneath to restore the proper elevation.
- Ensure the liner extends high enough to contain the flowing water.
To correct redirected water:
- Remove debris or reposition rocks to keep water flowing within the lined area.
- Adjust rocks causing excessive splashing outside the water feature.
Step 4: Inspect plumbing and filtration connections
If the stream and waterfall edges appear secure, inspect the plumbing and filtration components.
- Pipes: Look for cracks, damage, or visible leaks.
- Fittings: Inspect connections for loose or improperly sealed joints.
- Skimmer: Check the faceplate and surrounding liner connections for water escaping.
- BioFalls filter: Inspect the faceplate, fittings, and connected plumbing for leaks.
Repair or replace damaged components as needed.
Step 5: Inspect the pond liner
If the water level continues dropping while the pump is off, inspect the pond liner.
- Allow the water level to stabilize, if safe for fish and aquatic life.
- Examine the liner near the stabilized water level.
- Look for punctures, tears, folds, or damaged seams.
- Carefully move nearby rocks if necessary to inspect the suspected area.
- Repair confirmed liner damage using a compatible EPDM pond liner repair product and its instructions.
Common causes of liner damage include:
- Sharp rocks or objects.
- Damage during installation or maintenance.
- Animal activity.
- Heavy objects rubbing against the liner.
Step 6: Confirm the leak has been repaired
After correcting the suspected leak:
- Restore the pond to its normal operating water level.
- Restart the waterfall pump.
- Check the repaired area for escaping water.
- Monitor the pond water level for another 24 hours.
- Confirm that excessive water loss has stopped.
If water loss continues, inspect other potential leak locations. More than one leak may be present.
What if I still cannot find the leak?
If the source of water loss cannot be located after completing these steps, a qualified pond contractor may be needed to inspect concealed plumbing, liner damage, or filtration connections.
For additional assistance, submit a request through the Aquascape Customer Care contact form.