Water loss around a pond waterfall or stream is commonly caused by low liner edges, excessive splashing, debris blocking water flow, improperly positioned rocks, or leaking plumbing connections.
If your pond loses water only when the waterfall pump is running, the water is likely escaping from the waterfall, stream, BioFalls filter, or plumbing rather than through the main pond liner.
Follow these steps to identify and correct the source of the leak.
Step 1: Determine whether the waterfall is causing the leak
- Fill the pond to its normal operating water level.
- Turn off the waterfall pump.
- Monitor the pond's water level for 24 hours.
- If the water level remains relatively stable with the pump off but drops when the waterfall is operating, focus your inspection on the waterfall, stream, BioFalls filter, and plumbing.
Note: Some water loss from evaporation is normal, especially around moving water. However, rapid or excessive water loss may indicate a leak.
Step 2: Check for low waterfall or stream liner edges
Water can escape when the liner edge is too low, particularly where surrounding soil has settled.
- Inspect the edges of the waterfall and stream while the water is flowing.
- Look for wet soil, mulch, or gravel that may indicate water escaping over the liner.
- Identify areas where water is flowing over or approaching the liner edge.
- Carefully lift the liner and add compacted soil underneath to raise the affected edge above the water level.
- Reposition the liner and surrounding rocks to direct water back into the stream or waterfall.
Step 3: Check for excessive splashing
Waterfall rocks or excessive water flow can cause water to splash outside the liner.
- Observe the water flowing over each waterfall drop or cascade.
- Look for rocks directing water sideways or outside the lined area.
- Reposition smaller rocks to redirect water back into the waterfall or stream.
- If the pump has an adjustable flow setting, follow the pump's operating instructions when making adjustments.
- Check that the liner edges extend above the water level and contain the splash area.
Important: A small amount of splashing is normal. Water consistently splashing outside the liner can cause significant water loss over time.
Step 4: Remove debris or obstructions causing water to overflow
Leaves, algae, plant growth, and displaced rocks can create a dam that redirects water over the liner.
- Inspect the waterfall and stream for areas where water is pooling, backing up, or flowing unusually high.
- Remove accumulated leaves, algae, and other debris.
- Check for debris trapped underneath or between rocks.
- Reposition rocks that have shifted or are restricting water flow.
- Inspect the BioFalls filter and surrounding area for obstructions or overflowing water.
- Restart the waterfall and confirm that water flows freely within the liner.
Tip: Inspect streams and waterfalls regularly, especially after heavy rain or seasonal leaf accumulation.
Step 5: Inspect the waterfall plumbing
If the liner edges, splashing, and obstructions are not causing the water loss, inspect the accessible plumbing.
- Check the pipes and fittings supplying the waterfall or BioFalls filter.
- Inspect accessible pump and plumbing connections for signs of leaking while the system operates.
- Look for wet soil or standing water near plumbing connections.
- Repair any identified leaking connection using the appropriate repair procedure for the plumbing material.
Turn off and disconnect power to the pump before performing repairs.
Step 6: Isolate the leak if your pond has two waterfalls or streams
If your pond has two streams, waterfalls, or BioFalls filters, testing each feature separately can help identify which one is causing the water loss.
If each feature has a separate pump:
- Turn off one waterfall pump while leaving the other operating.
- Monitor the pond's water level.
- Switch pumps and repeat the test.
- Determine which waterfall or stream causes the water level to drop.
If one pump supplies both features:
- Check whether the plumbing has valves that allow each feature to be isolated.
- If suitable valves are installed, follow the system's operating instructions to isolate one feature at a time.
- Monitor the water level while each feature operates independently.
- Inspect the feature associated with the water loss.
Once the problem area is identified, repeat Steps 2–5 to locate the source of the leak.
Note: Do not block or restrict pump discharge unless the applicable pump instructions permit that method.
Step 7: Confirm the leak has been repaired
- Restore the waterfall or stream to normal operation.
- Make sure water stays within the liner throughout the waterfall and stream.
- Check that water is not pooling behind rocks or escaping around the BioFalls filter.
- Refill the pond to its normal operating level.
- Monitor the pond's water level over the next several days to confirm the excessive water loss has stopped.
What if the pond continues losing water?
If the pond continues losing water after checking the waterfall, stream, liner edges, and accessible plumbing, additional leak investigation may be necessary.
A qualified pond contractor can help locate hidden plumbing leaks, liner damage, or other difficult-to-identify sources of water loss.