A pond may lose water due to evaporation, splashing, plumbing leaks, low liner edges, liner folds, punctures, or plant roots. Before repairing the pond liner, identify where the water is escaping.
Step 1: Check for common causes of water loss
Before assuming the pond liner is damaged, inspect the following:
- Evaporation: Water naturally evaporates, especially during hot, dry, or windy weather.
- Low liner edges: Water may escape where the liner has settled below the normal water level.
- Liner folds: Folds that extend below the waterline can allow water to escape over the pond edge.
- Waterfall or stream leaks: Splashing, displaced rocks, or improperly directed water may cause water loss outside the pond.
- Plumbing leaks: Check pipes, fittings, and connections for visible leaks.
- Liner damage: Punctures, tears, and holes may allow water to escape directly into the surrounding soil.
Step 2: Perform a 24-hour water level test
If the source of water loss is not obvious, perform the following test:
- Fill the pond to its normal operating water level.
- Turn off the pump and waterfall.
- Mark the water level using a rock or another stationary reference point.
- Leave the waterfall pump off for 24 hours and monitor the water level.
- Compare the water level with the original mark.
Important: If fish are present, maintain adequate aeration and oxygen levels during testing.
If the water level continues to drop with the pump off
The leak may be in the pond liner or another area below the waterline.
- Allow the water level to continue dropping while monitoring the pond.
- When the water level stabilizes, inspect the liner around that elevation for punctures, tears, or other damage.
- Examine the skimmer faceplate and other penetrations near the water level.
If the water level remains stable with the pump off
The water loss is more likely associated with the waterfall, stream, plumbing, or filtration connections.
Inspect these areas while the pump is operating to locate where water escapes.
Step 3: Inspect the pond liner for damage
Once you have identified the approximate leak location:
- Carefully remove rocks, gravel, or decorations covering the suspected area.
- Expose the liner without causing additional damage.
- Inspect the liner for holes, punctures, tears, and plant roots.
- Check surrounding areas for additional damage.
Can plant roots cause holes in pond liner?
Yes. Although most plants do not directly puncture pond liner, their roots can grow through existing small holes and enlarge them over time.
Aggressive plants, such as bamboo, may also puncture the liner as their roots grow.
Avoid planting bamboo or other aggressive-rooted plants near ponds and water features.
Step 4: Repair a puncture or hole in the liner
If you locate a puncture or tear in a compatible EPDM pond liner:
- Clean the area: Remove dirt, debris, and moisture from the damaged section.
- Prepare the repair materials: Use a liner repair patch, primer, and seam products designed for pond liner repair.
- Cut the patch: Make the patch large enough to extend at least 2–3 in. (5–8 cm) beyond the damaged area.
- Apply the repair: Follow the repair product manufacturer's instructions for preparation, application, and curing.
- Inspect the repair: Ensure the patch is properly bonded without wrinkles or air bubbles.
Important: Use repair materials specifically compatible with the pond liner. Do not refill the pond until the repair materials have cured according to the manufacturer's instructions.
Step 5: Correct a leaking liner fold
If water is escaping through a liner fold near the pond edge:
- Carefully remove the rocks, gravel, or soil covering the affected section.
- Expose the liner fold.
- Pull the liner upward to eliminate the downward dip.
- Reposition the fold so water flows back into the pond instead of escaping over the edge.
- Make sure the liner edge remains securely above the normal operating water level.
- Replace the backfill and reposition the rocks or decorative materials to secure the liner.
Step 6: Test the repair
After repairing the liner or correcting the fold:
- Refill the pond to its normal operating water level.
- Inspect the repaired area for signs of leaking.
- Monitor the water level over the next several days.
- Check nearby liner edges and plumbing for any additional water loss.
- Once the repair is confirmed, replace any remaining rocks, gravel, or decorative materials.
How can I prevent future pond liner leaks?
- Inspect the pond liner and edges periodically for signs of damage.
- Keep bamboo and other aggressive-rooted plants away from the water feature.
- Ensure liner edges remain above the normal water level.
- Check for liner folds that may direct water outside the pond.
- Carefully reposition rocks and gravel to avoid puncturing the liner.
- Inspect waterfall and stream edges for settling or displaced materials.
Identifying the source of water loss before making repairs helps prevent unnecessary liner replacement and ensures the actual cause of the leak is addressed.