The Pro Air 20 Pond Aeration Kit and Pro Air 60 Pond Aeration Kit improve oxygen levels and water circulation, helping maintain healthy pond conditions for fish and beneficial bacteria.
These installation, maintenance, and troubleshooting tips will help keep your aeration system operating efficiently.
Tips for proper installation
- Position the compressor. Place the compressor on a stable, dry surface near a GFCI-protected electrical outlet. Position it above the pond's water level whenever possible. Never submerge the compressor.
- Verify check valve direction. Ensure the check valve allows air to flow toward the pond diffuser. Incorrect installation can restrict airflow or allow water to enter the compressor.
- Secure airline connections. Connect the airline tubing to the compressor and diffuser using the supplied stainless steel hose clamps.
- Prevent tubing restrictions. Avoid sharp bends, kinks, or obstructions that can restrict airflow.
- Position the diffuser. Place the diffuser in the pond according to the manufacturer's installation instructions.
- Verify operation. Connect the compressor to a GFCI-protected receptacle and confirm that bubbles reach the pond surface.
Helpful tip: Weighted Aeration Tubing stays submerged without additional weights.
- Weighted Aeration Tubing — 25 ft (7.62 m), Item #61011
- Weighted Aeration Tubing — 100 ft (30.5 m), Item #61014
Troubleshooting reduced or no airflow
If the Pro Air 20 or Pro Air 60 produces weak airflow or stops producing bubbles:
- Verify that the compressor is receiving power and the GFCI has not tripped.
- Inspect the check valve to confirm correct airflow direction.
- Check the airline tubing for kinks or restrictions.
- Inspect the rubber membrane diffuser for debris or buildup.
- Clean or replace the compressor's air inlet sponge filter if necessary.
- If airflow remains weak, inspect the internal diaphragm for wear using the applicable manufacturer instructions.
Important: Disconnect power immediately if a blocked diffuser or airline significantly restricts airflow. Operating against a severe restriction can cause compressor overheating.
Relevant replacement components:
- PRO Air Check Valve — Item #61003
- 10 in. (25.4 cm) Rubber Membrane Aeration Diffuser — Item #61010
- PRO Air Airline Tubing — 30 ft (9.1 m), Item #61002
Routine compressor maintenance
- Inspect the compressor's air inlet filter at least annually.
- Inspect more frequently in dusty conditions or if the compressor produces unusual noises.
- Remove the sponge filter, rinse it with clean water, and allow it to dry completely before reinstalling.
- Keep the compressor's air inlet free of leaves, dirt, and debris.
- Check airline tubing and connections periodically.
- Replace worn diaphragms using the correct model-specific replacement parts.
Always disconnect electrical power before performing maintenance.
Model-specific maintenance components:
- Pro Air 20 Compressor Renew Kit — Item #61015
- Pro Air 60 Replacement Diaphragm — Item #61007
- PRO Air Inlet Sponge — Item #61005
Winter operation tips
The Pro Air 20 and Pro Air 60 aeration kits can operate during freezing weather to help maintain an opening in pond ice for gas exchange.
- Position the diffuser approximately 12–18 in. (30–46 cm) below the water surface.
- Do not place the diffuser at the pond bottom during winter because circulation may disturb warmer water where fish overwinter.
- Protect the compressor from snow, ice, and moisture while allowing adequate ventilation.
- Monitor airflow and pond conditions throughout winter.
- Consider using a pond De-icer in addition to the aeration system.
Recommended winter product:
300-Watt Pond De-Icer — Item #39000
If the compressor will not operate during winter, protect it or store it in a frost-free location following the manufacturer's instructions.
Pro Air 20 and Pro Air 60 kit information
Pro Air 20 Pond Aeration Kit — Item #61009
- Maximum recommended pond volume: 5,000 US gal (18,927 L)
- Compressor power consumption: 15 W
- Included diffusers: One
- Included airline tubing: 30 ft (9.1 m)
- Maximum recommended pond depth: 6.5 ft (1.98 m)
View Pro Air 20 Pond Aeration Kit
Pro Air 60 Pond Aeration Kit — Item #61008
- Maximum recommended pond volume: 15,000 US gal (56,781 L)
- Compressor power consumption: 45 W
- Included diffusers: Two
- Included airline tubing: Two 30 ft (9.1 m) lengths
- Maximum recommended pond depth: 11.5 ft (3.51 m)
- Included manifold: Two-way airflow distribution manifold
View Pro Air 60 Pond Aeration Kit
Additional resources
- Watch Pro Air 20 & 60 Aeration Kits Tips and Tricks
- Pro Air 20 instruction manual
- Pro Air 60 instruction manual
- Browse Aquascape aeration replacement parts
If additional assistance is needed, submit a request through the Aquascape Customer Care contact form.